Step Instruction for Bathtub Installation

Click Here

Are you hunting for critical info on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


How to Install a Bathtub Yourself
Installing a tub isn't precisely rocket science, however it does call for strong plumbing, carpentry, as well as in some cases, tiling skills. Changing an old bath tub with a new one is likewise a reasonably hard task. If the old bathtub is readily easily accessible, the task can relocate rapidly; if you need to open a wall surface to eliminate the old tub and also place the brand-new bath tub, the job is a lot harder. In either situation, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub and set in the new one. Ensure you have actually qualified yourself for the task and also fit attempting it. Rather than working with a specialist to take control of a halfway-completed task, it is far better to take into consideration using one before you begin. Opportunities are you might need a specialist plumber to make tube connections.
This article will aid you mount a new bath tub in your restroom if you have already bought a new bathtub and don't need to alter the setup of your previous supply of water pipelines.
Your tools and also material list must make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Planning for the Installation


    First of all, the supporting structure provided with the bathroom should be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets unit to stop stress on the bath tub.
    Fit the flexible tap ports to the bottom of the two faucets making use of 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use every one of the provided washers.
    Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last position.

    Removing Old Touches


    If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is commonly the instance.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a towel all set for the continuing to be water that will originate from the pipes. Once the supply pipelines have actually been eliminated, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
    Prior to carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.

    Setting up the Bath tub


    Utilizing the two wood boards under its feet, put the bath tub in the required position. The wooden boards are handy in evenly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 small points.
    The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the bathtub till the level checks out level.
    To mount taps, fit all-time low of the outermost adaptable tap connector to the ideal supply pipe by making a compression join; after that do the same for the various other faucet.
    Switch on the water supply as well as check all joints as well as brand-new pipework for leaks and also tighten them if essential. Fill the tub as well as also inspect the overflow outlet as well as the normal electrical outlet for leakages.
    Finally, take care of the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the tub needs to wait till the bath tub has been made use of at the very least once as this will settle it right into its last position.

    Fitting New Touches


    If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the other end supplies a connection to the existent supply pipes.
    If you require to fit a monobloc, after that you will certainly require decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
    Next, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in place in between the tap as well as the sink. Protect the tap in place with the maker offered backnut. As soon as the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous kind should be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Tub


    In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split a rigid seal, causing the water to penetrate the wall between the bath and also the tiling, resulting in problems with moisture and also feasible leakages to the ceiling below.
    You can select from a selection of coloured sealers to blend in your components and installations. They are offered in tubes and cartridges, and also can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always load the tub with water prior to sealing, to enable the activity experienced when the bathtub remains in use. The sealant can split relatively early if you do not take into account this activity prior to sealing.
    Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water resistant sticky and grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Tools You Need to Install a New Bathtub

    I'm very fascinated with A Step-by-Step Guide to Installing a Bathtub and I am assuming you enjoyed the blog posting. In case you enjoyed reading our blog posting kindly do not forget to pass it around. Thank you for your time invested reading it.


    Reliable plumber? Dial!

    Leave a Reply

    Your email address will not be published. Required fields are marked *